DELL POWERVAULT 220S (SCSI)

Dell OpenManage Array Manager, v.3.6.0.568.5, A05
Array Manager software provides a comprehensive storage management solution in an integrated, graphical view. From a single location, Array Manager enables you to configure and manage local and remote storage attached to a server, while the server is online and continuing to process requests.

Maxtor Cobra 10K U320 36GB 68 Pin, Cobra 10K U320 36GB 80 Pin, Cobra 10K U320 73GB 68 Pin, Cobra 10K U320 73GB 80 Pin, Cobra 10K U320 146GB 68 Pin, Cobra 10K U320 146GB 80 Pin, v.DFX8, A02
This utility updates Atlas 10K IV drives from DFM0 to DFX8 version. This utility is for the following Maxtor drives: 8W581 - HD,146GB,SCSI,U320,10K,68P,MXT C4357 - HD,146GB,SCSI,U320,10K,68P,MXT U3987 - HD,146GB,SCSI,U320,10K,80P,MXT 7W584 - HD,146GB,SCSI,U320,10K,80P,MXT 7W578 -

Maxtor Aurora 15K U320 18GB 68 Pin, Aurora 15K U320 18GB 80 Pin, Aurora 15K U320 36GB 68 Pin, Aurora 15K U320 36GB 80 Pin, Aurora 15K U320 73GB 68 Pin, Aurora 15K U320 73GB 80 Pin, v.DTA1, A02
This utility updates Atlas 15K II drives from DT60 to DTA1 version. This utility is for the following Maxtor drives: U3989 - HD,18GB,SCSI,U320,15K,68P,MXT 8X892 - HD,18GB,SCSI,U320,15K,68P,MXT 9X923 - HD,18GB,SCSI,U320,15K,80P,MXT Y3402 - HD,18GB,SCSI,U320,15K,80P,MXT Y3403 -

Dell Backplane
This INF file contains support for Dell PowerEdge Servers and PowerVault storage products. This INF file will prevent the yellow warning from displaying in the Windows Device Manager.

Dell SCSI Hard Drive Firmware Utility
Do not power cycle your system while the update is in progress
This is a general maintenance release for SCSI drives. All former firmware releases for all supported SCSI hard drives have been compiled onto one release. Review the text file for information about fixes supported on this release.This version corrects hang issue found with PERC6/i and PERC5/i controllers after they have been updated to v.6.0.1-0080 and 5.2.1-0067, respectively.Seagate 10K7 and 15K4 SCSINew D405/D705 Firmware is available for Seagate 10K7 and 15K4 SCSI.This release addresses multiple minor fixes for data error handling, detection, and correction, and incorporates changes included in D404/D704, and will update Seagate Cheetah 10K.7 drive modelto firmware version D705 and Cheetah 15K.4 drive models to firmware version D405, respectively. With D403/D703, under certain rare circumstances a command timeout can possibly lead to drives being taken off-line, or cause the drive to post a SMART trip. Two changes are related to these timeout conditions: 1) idle operation and commands not being processed properly leading to possible timeout conditions2) particular error recovery taking longer than timeouts allow.Seagate 15K.5 SCSI New D507 Firmware available for Seagate 15K.5 Parallel SCSI Hard Disk DrivesThis is a general maintenance release that addresses multiple error handling and recovery enhancements and fixes that are considered to be corner cases but could impact overall performance of the drive. It is an optional upgrade that may be performed for maintenance or troubleshooting reasons. Fujitsu 10LX SCSINew 5E03 Firmware is available for Fujitsu 10LX SCSI Hard Disk Drives. This is a general maintenance release that has improved Write recovery, error handling and reporting.
This file contains a compressed (or zipped) set of files. Download the file to a folder on your hard drive, and then run (double-click) it to unzip the set of files. Follow the instructions to complete the installation.

Dell PowerVault 220S/221S SES Firmware
Known Limitations:

1. In Joined bus/Clustering mode, firmware is downloaded to both EMMs automatically (assuming that the second EMM is installed) by failing over and then failing back. In Split bus mode, however, updating firmware on one EMM does not automatically update the other EMM. Therefore, in order to update both EMMs, the user must download directly through the cable to each EMM.

   NOTE: It is strictly prohibited to have an Active/Active cluster while doing firmware downloads to avoid issues with the cluster.

2. When using Array Manager 3.1.1 (or less) in Clustering mode, EMM firmware can only be upgraded on the primary EMM (the left one when viewing the enclosure from the back). Therefore, in order to update both EMMs, the user must download firmware to each EMM individually.
3. If the PV22XS is configured with one EMM and one termination module in Joined bus mode, an error message will pop up when upgrading the firmware through Array Manager 3.1.1 (or less). This is an invalid error message in this scenario. If the fans have gone back to normal speed, then the firmware download was successful. To verify this, stop and restart the Disk Management Service. Then you can view the firmware version under the enclosure properties.
4. Firmware updates to enclosures attached to PERC 2/DC, PERC3/SC/QC/DC/DCL, or any PERC4 array controllers require that Array Manager be at release 3.4 or greater; while PERC 2/QC or PERC 3/Di controllers require that Array Manager be at least 3.5 or greater.
5. Important Linux Requirements:"libstdc -libc6.2-2.so.3" is required for running this application. If this library is not found on the system,the following error will appear.

   ./getSystemId: error while loading shared libraries: libstdc -libc6.2-2.so.3: cannot open shared object file: No such file or directory Collecting inventory..../PV2XXA00: error while loading shared libraries: libstdc -libc6.2-2.so.3: cannot open shared object file: No such file or directory

   In order to install the missing files, you would need to install "compat-libstdc -[Y.Y]-2.96.[XXX].i386.rpm" package from Red Hat distribution CD, where "XXX" is the version number of package and "Y.Y" is the release. Install the package as described below.

   E.g. on RH9.0 distribution do following:

   (Note: for RH9.0 the package to be installed is located on disc 1)

   # cd /mnt/cdrom/RedHat/RPMS # rpm -ihv compat-libstdc -7.3-2.96.118.i386.rpm (e.g. on RH 9.0 distribution)

This revision fixes a rare issue with the handling of SCSI bus parity error responses by the EMM. This may result in a SCSI bus reset and cause a pause of several seconds (depending on configuration) in I/O processing. The I/O operation will automatically retry and recover. There is no associated risk of data loss, security, long term reliability or other performance issues.
This file format consists of an archive of files that may be decompressed to a directory on the hard drive. The installation can then be done from that directory.

Dell Rack Advisor Utility, V5.0
This release contains Rack Advisor v5.0. Rack Advisor is a software application for use in configuring Dell servers and storage units into a Dell rack. There are different configurations allowed by region, based on the products sold in that region. There are four languages supported in this

Dell OMSIM Applications, v.2.2, A00
This is the EMC VisualSAN Version 2.2 Installation and Configuration Guide for PowerVault SAN environments.

Dell PowerVault 220S/221S SES Firmware, v.E.19, A10
The PV22xS_E19.bin file is the downloadable version of the enclosure firmware that provides management functions for the PowerVault 220S/221...